SPEND $60 & GET FREE SHIPPING
0

SPEND $60 & GET FREE SHIPPING

0

Your Cart is Empty

Use & Assembly

1

Assembly Instructions

2

Program Your Code

3

How to Anchor

4

Connect With Carriers

Video Instructions

Watch our assembly video to understand the ease of the LockBox assembly process. We also have a step by step guide below.

STEP BY STEP - LOCKBOX ASSEMBLY

  • Before You Begin

    - Make sure you have all the parts before beginning assembly.

    - For ease of assembly, we recommend laying the parts out in the same order as shown. 

  • Install the Batteries

    - Slide off the back of the battery case and install the provided AAA batteries

    NOTE: For use in temperatures below 0° Fahrenheit we suggest using Energizer Lithium batteries that are designed to be used in temperature as low as -40° Fahrenheit.

    LOW BATTERY WARNING: The lock will emit a repetitive beep every 3-4 seconds when the batteries are running low. When this occurs new batteries should be installed.

    *Never use old batteries or mix Lithium and Alkaline batteries. It will affect the performance of the device.

  • Step 1 - Attach Wall Panels

    1a - Attach Left Side Panel (B) to Back Panel (C) and secure with screws.

    1b - Attach Right Side Panel (D) and secure with screws

    1c - Attach Front Panel (E) and secure with screws.

  • Step 2 Attach Bottom Panel

    2a - Flip LockBox upside down.

    2b - Place Bottom Panel (F) onto box and secure with screws.

  • Step 3 - Attach Lid

    3a - Flip LockBox upright.

    3b - Attach Lid (A) to Back Panel (C) and secure with screws.

    NOTE: Lid hinge should not go past 90°. Your partner should hold the lid in place through step 4.

  • Step 4 - Attach Lid Struts

    4 - Attach the Lid Struts (G) to the Side Panels and Back Panel. The Lid Struts will click into the connectors. 

    NOTE: Keep Lid open for ease of setting your personal code.

Video Instructions

Watch our programming and reprogramming video to set up your LockBox code. We also have a step by step guide below.

STEP BY STEP - PROGRAM YOUR CODE

  • Set Your Personal Code

    1. Press the "#" button twice
    2. Enter the preset factory four digit passcode (0000)
    3. Press the "#" button twice again
    4. Now enter your desired four digit passcode
    5. Press the "#" button twice-you should hear two beeps
    6. Once the lock beeps twice, your personal code is set

    To open the box, simply enter your four digit code and then press the "#" button. The lid will pop open.

    NOTE: If the light on the LockBox screen turns off while setting up your code you will need to start over.

  • Change Your Code with Your Key

    1. Use the key to manually open the box
    2. Hold reset button inside the box for five seconds
    3. Once the lock beeps you are ready for new passcode
    4. Press the "#" button twice
    5. Enter the desired four digit passcode
    6. Press the "#" button twice-you should hear two beeps
    7. Once the lock beeps, your new personal code is set

    NOTE: If the light on the LockBox screen turns off while setting up your code you will need to start over.

  • Change Your Code

    1. Press the "#" button two additional times
    2. Enter your curChange Your Coderent four digit passcode
    3. Press the "#" button twice again
    4. Now Enter your desired four digit passcode
    5. Press the "#" button twice-you should hear two beeps
    6. Once the lock beeps twice, your personal code is set

    NOTE: If the light on the LockBox screen turns off while setting up your code you will need to start over.

Video Instructions

Watch our anchoring video to secure your LockBox on your porch or wherever you’d like to place it. We also have a step by step guide below.

STEP BY STEP - HOW TO ANCHOR

  • Before You Begin

    Place the LockBox in desired location. The back of the LockBox needs to be at least 2 inches away from any wall or other surface before you begin to anchor. This will allow the lid to open properly without interference

  • Step 1 - Drilling Anchoring Holes

    - Using your power drill with the masonry bit (included), insert the bit into the open hole in one of the four bottom corners and drill into the ground. (Please note: this drill will work on wood or concrete).

    - Repeat drilling in all four corners.

  • Step 2 - Anchoring LockBox to Ground

    - Remove the masonry drill bit from the drill and insert the Phillips driver bit.

    - Using the power drill, insert one of the screws provided into the open hole in one of the four bottoms corners and secure it to the ground. 

    - Repeat fastening screws in all four corners.

CONNECT WITH CARRIERS

We recommend reaching out to your delivery carriers via their mobile app, website, or phone to ensure your packages are placed safely inside.

Technology not your thing?Another option is to talk to your delivery driver when they are at your house with a package. Share your code with them and they can update your information on their end for future deliveries. 

TIPS & TRICKS

Use your magnet and door hanger.

If you place your LockBox away from your front door, use the door hanger to list where it is located so that your carrier can find it and ensure your packages are placed safely inside. Use the magnet on your LockBox to show your carrier instructions on how to properly access and place packages inside.

Talk to your carrier face-to-face.

The quickest way to get your code to your carriers is to talk to your delivery drivers when they are at your house with a package. Share your code with them and they can update your information on their end for future deliveries.

The best batteries for colder climates.

We suggest using lithium batteries for colder climate areas which are designed to be used in temperatures as low as -40° Fahrenheit.